BMW E92 335i - progress thread

[Frode D]

Man that looks amazing!

Thank you!

[244Brick]

Man that looks amazing!

[Frode D]

I actually brought my camera with me to the garage this time but did just snap a few shots.

The back of the tank:




Full of MDF-dust after fabricating the trunk floor. Does not go low enough with 19"

[Frode D]

Gonna do this in norwegian.

Hvor har du henta styrestrøm? hadde lignende problem med mitt V2 system. da hadde jeg henta styrestrøm fra en plass jeg ikke husker helt, men det gjorde i allefall så jeg ikke fikk brukt preset mode og det starta opp av og til av seg selv.

Jeg har henta styrestrøm (ignition) fra 12V uttaket i bagasjerommet. Sigarettenneren om man vil. Brukte samme sted når jeg hadde e-level. Jeg har også prøvd å koble til ignition direkte på batteriet men hadde samme resultat da også.

Har også gått over alt av jord og +ledninger. Skjønner ingenting.

[stbk]

Gonna do this in norwegian.

Hvor har du henta styrestrøm? hadde lignende problem med mitt V2 system. da hadde jeg henta styrestrøm fra en plass jeg ikke husker helt, men det gjorde i allefall så jeg ikke fikk brukt preset mode og det starta opp av og til av seg selv.

[Frode D]

Awesome work!!

Thank you!

Less teaser more wheel!

Love the work and the car, awesome.

I know I know, but the wheels are not finished yet, and that is the only picture I've got..

-

Finally the car is back on bags. Swapped the rear bags to SS5 and shocks to Bilstein touring. When installing the front struts I realized one of the camber plates were almost maxed out. And I have been running just close to 2 degrees. Turns out I have gotten two left camber plates. I don't have time to wait for new ones so I just redrilled the old ones and moved the bolts.



Controller is live!


BUT, I do have some trouble with the V2 system. Everytime the compressor is done building up pressure and stops, the V2 system reconnects. This causes the calibration to end before it is done and causing some issues with bleeding off pressure in "Preset Mode". the only way to bleed off is to du it in "Manual Mode" or the setting with 0psi. Her is a video of when I try to calibrate:

https://flic.kr/p/rgrWbg

[shredgnar_]

Less teaser more wheel!

Love the work and the car, awesome.

[DinanDave]

Awesome work!!

[Frode D]

Finally got some motivation to continue on the trunk setup. Pulled the lines to the bags and started to make the false floor in the trunk. Also started bending the hardlines.

Forgot my camera, but I got some shitty pictures with my phone.









A teaser of the new wheels. Only pic I've got for now.

[Frode D]

Have seen this car many, many times before but it never hurts seeing it here aswell! Awsome mods man

Damn, just gets better and better.

Like it alot.
I'm a Futura fan for sure.

oh man, i can not wait until i can start building my air setup

Thanks a lot guys

[Roccy_Miyagi]

oh man, i can not wait until i can start building my air setup

[gooders]

Like it alot.
I'm a Futura fan for sure.

[NeilP]

Damn, just gets better and better.

[Poppy]

Have seen this car many, many times before but it never hurts seeing it here aswell! Awsome mods man

[Frode D]

amazing

Respect for getting all the small details finished in the correct way. Looking forward for more updates

Goddamn you! Your car at it's worst is better than my car at it's best, love it man

solid job on the retrofit in the vent ! love it when people take their time and do a good install . looks tits

Appreciate the kind words guys, thanks!

Familiar places on the pictures, I used to live in that area.

Oh, are you Norwegian?