Project : BluePrint

[blurred]

[blurred]

It's growing on me. I'll feel better about it tomorrow when I am able to see it out of the garage and from a distance.

However, I need some 3/4" spacers for the front and some 1" spacers for the rear. Probably just going to push it and do 1" all around but that will be determined after some more measuring.

[smiles]

Front and rear on the truck. Rear one needs tape still, as well as the two on the other side.

Looks killer man! Can't wait to see what you do next.

[blurred]

Front and rear on the truck. Rear one needs tape still, as well as the two on the other side.



rear profile shot


and a couple different angles of the front

[blurred]

Appreciate it guys. I'm very pleased with how this thing has turned out so far. It will be fun to take this for an actual photo shoot once I get everything back together and cleaned up.

[FRSBrndn]

That Bugatti interior though! Damn homie. Looks realllllllll good.

[Red_Arrowheads]

it will most likely be something involving multiple pieces.

NOICE

But I will have to save for a long ass time.

That's my reaction to everything involving my G8. Saving for upgrades is the story of my life.

[blurred]

Like, two or three..

Any more than that would probably not be a very good option to drive on.

[Shaun708]

Oh boy did u say multiple pieces

[blurred]

Oh, but the flares are painted.

Front flares


Rear flares


Once these cure, I'll be able to wet sand and buff them out.

[blurred]

Right now, I will be running the current set that I have, just spaced out enough to line up with the flares and fill the gap, which is about an inch or two based on my guestimates.

Future wheels are going to be something I have to figure out... With this type of offset/width that I can now run and not wanting to run spacers forever, it will most likely be something involving multiple pieces.


























But I will have to save for a long ass time.

[Red_Arrowheads]

Those flares look freakin' amazing!
What wheels are you planning on running now that you have so much room for wheel-related activities?

[blurred]

Is Smash Burger down in Murfreesboro? That's the only one I could find near me...

And I will include an update:

Was able to get the bumper off the shelf, install the new accent lights in the two vents and install the bumper on the truck. Since I needed to make sure the bumper sat where it should so I didn't have to move it again, I installed the front two flares as well. This gave me a good idea how they will sit and look when painted. I'm very pleased...









and I have the back two sitting in the garage waited for the (hopefully) last coat of epoxy to dry completely.



Paint has been shipped. Once that gets here and I finish the back two flares, I'll be painting the handles, smooth gas door and flares.

[Duffy]

Never been to a smash burger meet. And not confusing your car with something on ebay wheels, it was the backend of a car that looked similar to yours as well as a drop. But, if you weren't in the area, then it obviously wasn't you.

Hell, the truck is probably unrecognizable at this point since I have so much of it removed.

Anyway, you have any more details about this smash burger thing?

I did have ebay wheels at one point...not really "details" but everyone used to meet up at Smash Burger (Last Summer) before heading out to the 1/8th mile strip around 10-11...it's a pretty chill evening, everyone is usually pretty tame. There are a few mini trucks and one particular boosted v8 S10 I remember specifically. When I get back I'll have to talk to my buddy to see if they still go there or not.

[blurred]

Never been to a smash burger meet. And not confusing your car with something on ebay wheels, it was the backend of a car that looked similar to yours as well as a drop. But, if you weren't in the area, then it obviously wasn't you.

Hell, the truck is probably unrecognizable at this point since I have so much of it removed.

Anyway, you have any more details about this smash burger thing?