If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Nice collection Anthony, I need to figure out what I am going to do with my collection yet.
Not sure if I should cart them all over or just leave them in the garage until I have a place of my own...
Could be a stupid question but I'm looking to have Whitehorse make me up barrels and lips to suit bbs 16" 34 hole centers. I've emailed them and they want me to fill out the chart so they can spin them up but I don't really trust myself to get the measurements accurate enough for this kind of thing. Don't really have the appropriate tools to get precise enough. (I don't think a measuring tape will cut it)
Wondering what the chances are of anyone having a link to measurement info (specifically the face) or the ability / advice on measuring one up?
If you're happy to do that I'm down for it. Probably the safest bet to give them a center as I want 6 barrels made and 4 lips. Which is why I want to get it right the first time. I suppose I could just post it directly to them though to save you the hassle lol
Hnnng, custom spun lips and barrels from Whitehorse Anthony?
Have you thought of just going through Felgenfuchs.de?
That's where I have bought all my stuff previously, quite nicely priced.
Can also get Radinox lips
That's what I'm doing with the 15's once I have enough/any money.
Yeah Seb would be good but I want to step 16 to 18" so need to be custom through Whitehorse or rotiform. Whitehorse will be cheaper and prefer to support what they're doing for aus.
Do it. Build the rs. If you've already got all the bits it just makes sense yeah?
just ran across this post on another forum about tumblers, interesting to see his 2-stage setup, cleaning first then polishing with different media...
This is what I then did. first off, get your curse word rusty ass nuts and bolts.
Then, add to the tumbler, media, about 1/5 full of water and some washing up liquid.
Crank the lid down, leave to run for 12-24 hours in the garage
Open it up
Use a dental pick to get the pyramid media out from where it doesn't belong
Marvel at how it worked when you did precisely nothing but twiddle your thumbs for a day.
Clean off the bits in some water and kerosene
Well sheeeiiit, it only worked!
Now take all those bits, dry them off as best you can, then take the walnut shell, no water this time.
Some generic metal polish
Throw in your dried off bits and pieces
Get it going
Wait another 12-24 hours
HELL YES. The polish is silicone based, ALL this hardware is now prepped and ready to go to the platers for some cadmium plating (the guys who did my struts) really amazed at how well this works, considering I have to exactly zip all. The thing with getting a good plate, is having the part prepared and the smoother it is, the better the plate will adhere and look when its done.
Yeah Seb would be good but I want to step 16 to 18" so need to be custom through Whitehorse or rotiform. Whitehorse will be cheaper and prefer to support what they're doing for aus.
Do it. Build the rs. If you've already got all the bits it just makes sense yeah?
Ah, I was unaware of the step, makes sense now! Whitehorse for sure then!
if you can tuck the 16" RS's on the square that would be swell.
Will definitely be tucking because have to be legal, and I don't know how much she's going to squat at the rear when she's packed full of my shit plus a set of steel wheels strapped to the roof racks.
Build the 16's for it.....if you've got the bits, why not!
My thoughts exactly. Will start test fitting the rears up once I have the drums installed on Saturday.
Anth, all this tumbler talk makes me want to get one for the countless rusted RS bolts I have. May have to consider purchasing one or borrowing someone elses and getting the media etc to use.
Sarcasm is easily calculated on vortex dude. Take 4 parts GLI lip and divide by BBS RS. If you are left with a remainder, subtract it from omgmoarlow. Profit.
Comment