Announcement

Collapse
No announcement yet.

Aussie wheel tech/discussions

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • hakhawk
    replied
    wanting to widen my wrd's, anyone got lead on someone who could do lips of similar design. already spoke to Craig at whitehorse and its a no go from him, three-piece.us have rolled lips.

    if I went all 4 lips id be fine, but I only wanted to replace the rears, and reuse the old rear lips on the front

    95470813_2271998339761373_4604735159319658496_n by troy, on Flickr

    95091608_609773409611980_6015438251685314560_n by troy, on Flickr

    Leave a comment:


  • skytup
    replied
    anyone have any info on these bbs rt065 (cruise), never seen this design before

    Untitled by matt morgan, on Flickr

    Leave a comment:


  • rom2nv
    replied
    Freshening up my Futuras. I don't need to split them but do need to remove the bolts. Should I reapply sealant (I did it myself on this set when I split them last time) or is the likelihood of an air leak nonexistant?

    Leave a comment:


  • Lukey
    replied
    Any 15" 4x100 centers/wheels for sale?

    Leave a comment:


  • GJA003
    replied
    Anyone able to recommend someone for sandblasting ?
    Really need to finish these wheels.

    Leave a comment:


  • PhilTho
    replied
    Anybody know if Weds Kranze Cerberus 1's are welded 3pc?

    Leave a comment:


  • GJA003
    replied
    Originally posted by dylan8 View Post
    I use to bring heaps in, currency rate is a killer now.
    Send me what you specs you want and ill get a price for some local ones.
    pcd to pcd
    width
    number of
    bolt/thread and pitch on car
    stud size wheel side
    centre bore car side
    centre bore wheel side
    PM Sent

    Leave a comment:


  • dylan8
    replied
    Originally posted by Lukey View Post
    The sticker says 16x7 +38 (i think its 38). I did take a pic of a ruler with a bit of wood against the back of the wheel.
    yep looks to be 7et38 by the measurement

    Originally posted by GJA003 View Post
    Anyone know any good places or dealers in Australia for adaptec or any 4X100-5X120 adapters
    I use to bring heaps in, currency rate is a killer now.
    Send me what you specs you want and ill get a price for some local ones.
    pcd to pcd
    width
    number of
    bolt/thread and pitch on car
    stud size wheel side
    centre bore car side
    centre bore wheel side

    Leave a comment:


  • GJA003
    replied
    Anyone know any good places or dealers in Australia for adaptec or any 4X100-5X120 adapters

    Leave a comment:


  • Lukey
    replied
    The sticker says 16x7 +38 (i think its 38). I did take a pic of a ruler with a bit of wood against the back of the wheel.





    Looking to go into the region on x8 - x9, would have to work out offsets and stuff and see if x9 is even possible. The only issue i have with the barrels on there now is that if i run any amouny of camber more than like -3 i scrub a fair bit over bumps on the inside of the rear archs

    Leave a comment:


  • Craig Winters
    replied
    What are the specs now and what do you want to achieve? If you can get away with making new outer lips only then better for you $ wise.

    Craig.

    Leave a comment:


  • Lukey
    replied
    I dunno if these are any good??





    Leave a comment:


  • Lukey
    replied
    ill just whip it off and wash it then get some pics

    when i get a chance!

    Leave a comment:


  • dylan8
    replied
    Yeah can leave tyre on. Dunno how skilled you are taking a pic of inside of the back of a wheel while it's fitted up though haha

    Leave a comment:


  • Lukey
    replied
    Originally posted by dylan8 View Post
    got a close up pic front and back? be easy to tell if it can be done or not without doing any cutting?
    Can the tyre still be on? Im currently running them on the car lol

    Leave a comment:

Working...
X