LS1 Drift Build 'Nuff Said'

[Exami]

did not know that.. Well its not a brand new motor so I should be good.. We will see.. lol

Facts behind that is, if you have just made machining work or honing to your engine, the piston rings will eat more of the cylinder wall if you use mineral oil, this makes the piston rings seal better. if you havent done any machining to the engine its fine.

Also if you have done machining, you should run the engine couple times, before reaching high oil temp and change oils after first time reaching 'high' oil temp to remove any residue that might have left from the machining work.. just to be sure.. and for that purpose the cheap mineral oils are pretty ok

Other than that, nice build keep it up!

[bostongrnM3]

so nice to see this thing running after 3 years of following this build. cant wait to see vids of it running 100%

[Teeson1111]

congrats man! first fire up feels good eh?

[Royal_T]

I always heard not to use Synthetic for break in's. I always used Joe Gibbs. Congrats on the startup!

did not know that.. Well its not a brand new motor so I should be good.. We will see.. lol

oh damn that sounds mean as shit.

I love it

THanks Mean is what I was going for..

niiiiiiice

Thanks

Did he Weld up the pie shaped holes in the wheel wells or Just FG them? Looks good!

Yeah he welded up those pie shaped holes.. And thanks for the kind words..



On a side not have a guy coming over tonight to check out why it is idling so rough.. Crossing vids I have another vid for you guys later .

[benz88]

Did he Weld up the pie shaped holes in the wheel wells or Just FG them? Looks good!

[Miroteknik]

niiiiiiice

[SnazzyQ]

oh damn that sounds mean as shit.

I love it

[Jlyons617]

I always heard not to use Synthetic for break in's. I always used Joe Gibbs. Congrats on the startup!

[Royal_T]

Okay Time for a legit update... So lets get this Mutha****nParty started..



As I stated before I love Wheat beers and Karbach Brewing Co. makes a damn good. one..



And you know this post would not be complete if I did not post up some DogFish Head..



The DogFish Head Piercing Pils has a very unique taste.. i dig it though.



Started off running my Hydro Brake lines to the rear..



Ran it through the center console and then T'ed it in the rear..



Went under the Accusump, Nice and clean.. Now I still have to run all my brake lines though..



You know things are getting close when you start buying all your fluids



Damn that is a lot of oil.. Have to fill the Accusump also..



Going to make sure this bad boy stays cool..



A quick look at her before I send her off to Dallas to finish wiring



Damn she is one sexy lady..



Loaded her up on these damn Uhaul trailers,, Can't wait to buy my own once she is done.. (Just take a guess which trailer I am aiming for)



I think the only thing I like about this trailer is the tire tie downs..



Dropped her off at Stew's house.. And she is in good hands.. and also has some nice company with her..



**** is about to get real.. some cutting..



Sad sad day..... But the out come will be epic











Have to water proof and smoke proof these bad boys..





The Start of my floor board so my feet have some were to rest and not get hot..








I just love how this thing is turning out..



Need grip no problem.. Love how it turned out in the end with the grip tape and all..



Let the wiring begin..




Love this location of were my breaker is..



Out of sight





Let there be light!!!




So badass to see everything turn on...






entering the cabin



Now let the ChaseBays **** fest begin...




Stew found the issue why the PCM would not turn on.. Was getting constant power were it should have not..



Like WTF!!








Issues fixed and put back together



After all that we need to rename this harness



On to removing all the unnecessary wires for lights..




First time I have seen lights light up on this car for about 3 yrs.. so stoked.




Install my IAT sensor



Time to remove this 3yr old gas.. It was nasty to say the least.. and I had like 7gallons of it..



Before we stated we wanted to reroute the fuel lines better.. So more fittings were ordered..



And this cute little filter




Oh **** we have pressure.. We def bumpped this up with my FPR... But man over 3yrs its good to see some pressure.. lol




PCM is talking so lets do this..


http://vimeo.com/103854495

Okay what all you guys have been waiting for.. Now I post everything on this build the good and the bad.. So with that being said I think this is Bad...LOL my timing is all jacked up so we are working on the issue as we speak and I should have a better idle vid for you soon.. But Like I promised we have a heart beat.. So stoked right now..

Now I got to hear this thing in person and man is it loud and rowdy, just how I wanted it to be.. can't wait to rip in this thing

[aeion]

It's just crazy some of the stuff that I've read about their harnesses. Garbage man.

[Royal_T]

It's funny how the import magazines rave about how awesome Chase Bays is and then I see stuff like this that seems to prove the polar opposite. On a positive note, I can't wait to hear this thing spark up.

I know, they must be kissing some serious ass.. They even sponsor some FD drivers.. They are truly a pile of shit...

So that's what Stew has been working on lately haha

Saw the crap on FB. Sorry to see how much of a mess all of that was man.

Yeah Man Stew been busting his ass on fixing all the shit they did.. I don't understand how you can miss up a easy harness.. But we got it now..


Update I should be heading up to Dallas this Friday so look out for vid post..

[aeion]

So that's what Stew has been working on lately haha

Saw the crap on FB. Sorry to see how much of a mess all of that was man.

[DeltaAlpha9]

It's funny how the import magazines rave about how awesome Chase Bays is and then I see stuff like this that seems to prove the polar opposite. On a positive note, I can't wait to hear this thing spark up.

[Royal_T]

man i thought chase bays was reputable

LOL I hope that was a joke.. They been getting bashed hard..

[244Brick]

man i thought chase bays was reputable