JZZ30 Form and Function Come Together

[190Evan]

Got it sorted! Swapped the ECU for a gs300 jz-ge ECU and it started but ran like shit so I reinstalled the original ECU and now it runs. Turns out I have leaky capacitors in my ECU so I ordered some and Im going to repair it this week. In other news I FINALLY got my rear lip mounted and it looks cool.



Also my girlfriend bought me a replica steering wheel to match my replica everything lmaoo

[storey618]

Its' automatic, I'm gonna pull the starter out and inspect all of the wiring and everything.

oh my bad homie. could have swore i remembered reading that it was a manual.

[190Evan]

try rolling the car and then popping it in gear. from the sounds of it your starter isnt lined up to the flywheel. also after you put the new starter in are you sure you hooked all the wires up and did it correctly? the clicking could either be misalignment or just not enough power

Its' automatic, I'm gonna pull the starter out and inspect all of the wiring and everything.

[storey618]

HELP!

Hey guys, so for the last week I have been searching on the forums (including this one) and all over AllData for the possible cause of my problem. Here's the low-down...After school last week I started the car and drove to work and everything was 100% fine no issues at all driving there. I parked it and went to work and when I came back to the car to leave I went to start it I got this horrible grinding sound coming from the starter. Now beware this car is lowered but I inspected the harness and it was not even touched nor damaged and then I relocated it. Still no start and still a grinding sound. I then tried to turn the crank clockwise by hand with a breaker bar and I couldn't even get it to turn with my foot kicking it which scared me but I just assumed I wasn't strong enough to over come the compression. So I bought a Re-manufactured starter from Napa and it looked super solid. I installed it and the sound went from cranking and grinding to clicking with no crank at all. I assumed my old crap battery was dead because I live in Arizona so I went ahead and replaced it and still no luck. When I go to start it the relay clicks and the lights shut off. For a second I thought it would be the Crank position sensor but the car would still at least try to crank if it was that. So now I am stuck with no car and no transportation and I am lost. As of now I am going to inspect the wires going to the starter but I don't see why they would all of the sudden just take a crap on me and leave me stranded. Any help is appreciated!

try rolling the car and then popping it in gear. from the sounds of it your starter isnt lined up to the flywheel. also after you put the new starter in are you sure you hooked all the wires up and did it correctly? the clicking could either be misalignment or just not enough power

[190Evan]

HELP!

Hey guys, so for the last week I have been searching on the forums (including this one) and all over AllData for the possible cause of my problem. Here's the low-down...After school last week I started the car and drove to work and everything was 100% fine no issues at all driving there. I parked it and went to work and when I came back to the car to leave I went to start it I got this horrible grinding sound coming from the starter. Now beware this car is lowered but I inspected the harness and it was not even touched nor damaged and then I relocated it. Still no start and still a grinding sound. I then tried to turn the crank clockwise by hand with a breaker bar and I couldn't even get it to turn with my foot kicking it which scared me but I just assumed I wasn't strong enough to over come the compression. So I bought a Re-manufactured starter from Napa and it looked super solid. I installed it and the sound went from cranking and grinding to clicking with no crank at all. I assumed my old crap battery was dead because I live in Arizona so I went ahead and replaced it and still no luck. When I go to start it the relay clicks and the lights shut off. For a second I thought it would be the Crank position sensor but the car would still at least try to crank if it was that. So now I am stuck with no car and no transportation and I am lost. As of now I am going to inspect the wires going to the starter but I don't see why they would all of the sudden just take a crap on me and leave me stranded. Any help is appreciated!

[190Evan]

Kind of lost with what I want to do to this car at the moment, I don't have the space or time to do a JZ swap and the manual swap is also pretty much worthless IMO unless I go with the CD009 swap and I haven't been able to put together a full parts list to ensure it would be fullproof so I'm holding on that until I have a space to garage the Lexus and tear it up apart and do it right and not rush it. Other than that all that has changed is I got a boxer and shes stealing all of my car parts money at the time haha.



Managed to get some new brakes fitted and then I realized I really need to just upgrade to the Ls brakes or some sort of BBK because these are a joke.



Picked up some maintenance parts before I even bother messing with modifying this thing. Question for any 2J powered guys out there, Turbo or not do you guys reccomend switching back to the OEM platinum plugs or do you think coppers will cut it for now? I've heard people say they had issues with copper plugs in these motors but with them properly gapped I haven't had any issues so far, not sure about the life span though.



Also got a chance to put together a shelf in my joke of a work space lol.



Anyways kind of lost motivation in this thing for right now and I just don't know what I want to do with it anymore. Any ideas appreciated but I'm not trying to dump this thing or tuck anymore lol.

[190Evan]

Hey Guys

not much of an update but I thought I might as well put these pics in here because I guess while I was unable to post on here for a while I never got a chance to share them. I've never had anyone actually shoot my car with a camera and still have yet to but I think this is the best picture I've taken of my car thus far with my iPhone (not a current photo).



The rest of the photos are pretty much just some cool cars I've seen around my campus (UTI Avondale). I guess it was dumb of me to not expect to see rad cars at an automotive school lol. Anyways here's a few s13's



I believe this is one of the teachers at my school and I'm not usually into these type of cars but this thing is just nuts. SO rad irl.



Another kid at my school who slides (obviously) I believe his name is Pedro? Thing is pretty rad.



and last but not least... My FAVORITE car in the lot lol, This beautiful turbo diesel w124 on reps lol. Thing could definitely use a drop but it's just so damn clean, makes me miss mine everyday haha.



Not much going on other than me doing some maintenance before the next drift season starts here. New front ceramic pads and drilled and slotted rotors, valve cover gaskets, pulleys(not harmonic balancer), spark plugs, plug wires, and other various gaskets and things here and there. I'll make sure to snap some shots. Other than that I'm just trying to figure out what I want to do manual swap wise. I'm almost completely set on the CD009 swap but the w58 keeps popping into my head because of how easy and fullproof it is but its just too weak for what I'm doing. Any insight would be appreciated or parts list for the CD009 swap. Till next time.

[190Evan]

300hp to the tire or at the crank?

You'd need to port the hell out of that head, get some agressive cams and bump the compression up to even get near that.

Also check out grounding kits. They have for the most part been forgotten about or dismissed as fake, but on older cars that have poor factory grounds they actually do help. Here's a dyno from the Tila Tequila issue 12 years ago.

I changed my mind on the NA power thing sadly, because of my budget I'm going to 1jz swap it for now, somewhere down the line I would like to build an NA 2j it would just require a full tear down this motor really needs it.

[imschwaggy]

love these

[rice4life]

300hp to the tire or at the crank?

You'd need to port the hell out of that head, get some agressive cams and bump the compression up to even get near that.

Talk to Brendan for more info

http://clubroadster.net/vb_forum/90-non-roadster-projects/46603-my-itb-time-attack-supra-high-horsepower-not-found-p.html

He has more threads around, this one is kind of dated.

If you upped the compression to around 12.0:1 you might be able to get around 270 whp with the aforementioned mods. You don't need ITB's though, they are good because you can tune them by changing velocity stacks and the throttle response is increased, but you might be able to achieve similar results from modifying a JDM non banjo bolt GTE upper intake mani onto the GE lower mani and porting it as well with a BBTB. The shorter runners of the GTE intake mani and less bends will give you more peak power.

Turbodremz on clublexus did that, and it worked well for him.

http://www.clublexus.com/forums/sc-1st-gen-1992-2000/514354-anyone-using-2jzgte-manifold-on-a-2jzge.html

Also check out grounding kits. They have for the most part been forgotten about or dismissed as fake, but on older cars that have poor factory grounds they actually do help. Here's a dyno from the Tila Tequila issue 12 years ago.

[190Evan]

Pics don't work.

Fuuuuuuuuufixed

[becausephilchow]

Pics don't work.

[190Evan]

Update time yo

It's been a solid minute since I've updated this thread mostly because I'm going to UTI all week long and have no computer . I haven't been able to even upload photos to photobucket or Imgur because they are blocked but whatever I think I found a way around it now.

Well not much has happened I have only really gotten my kit mounted except for the rear bumper lip (I'm lazy) and I've just been chasing electrical issues and getting the car mechanically sound for the most part. I also lost my job so I haven't been able to get any parts or at least save up for the 1jz swap i want to do.

First off here's a little pic of the sc300 with my friends RB25 swapped s14 and a 2j-gte swapped mk3.



Also for anyone interested in my super cool coils lmao



Here's a pic at the local track (Wild Horse Pass Raceway)



I had a difficult time making the high beams fit with the shitty kit I ended up buying and then i realized that I **** the way Sc's look like early 2000's E class mercedes haha so I'm going to shave them and get it painted eventually.



Then I ran into some issues. 4/6 Spark plugs were fouled, the primary ignition coil wire was being ripped by a zip tie previously installed by PO, The MAF was bad, the TPS went bad, and I had open in the ground circuit of the MAF. Fixed all those after the shop told me they couldn't source a MAF for my car. Oh btw they also didn't even bother diagnosing the issues other than just the bad MAF. Got them fixed and it's running perfect again.



I also managed to half diagnose my AC problem, there was an open in the power circuit for the compressor so I hotwired a relay o a switch and I'm running it manually off of that... Soon after I realized my brain isn't both a high and low pressure switch and that manually controlling it could possibly ruin my Evap or other things so I don't really bother using it. Eventually I will just delete AC all together when I do the 1JZ swap. Anyways here's the little switched fitted in the cabin.



Also had this banner that I made in high school laying around so I slapped it on. (kudos if you spot the NUT button lmao.



The aftermarket headers also forced me to extend my o2 sesnor wires so like 5 minutes of Ohm's law later and boom I bought the supplies and went for it. They work perfect.





Other than that I haven't done much more besides basic wire fixes and little sensors here and there. Here's some cool cars at my local car meet at the Pavillion in Scottsdale, AZ.





Jeez I really need to update my sig and profile picture lmao

[Golden Gramps]

That moment when your LS won't cut it anymore. This is going to be great!

[TWM Performance]

Love it! Can't wait to see the 300hp NA, gonna rip so hard and have amazing response.

- Renato