datsun 620 truck. doin low low things

[pejsa]

ok so today i did a little cosmetic trick with my side markers to make them look less bulky, basically what i did was mount them from the inside of the fenders.

before


after




love how lazy the people were that painted this truck

i also put on a little foam filter i had laying around since the clamp on my oem filter broke (not because I'm trying to make this turd faster lol)


lowered the ass another inch.
fittment test =]

[pejsa]

for the guy who asked for an exhaust clip here you go.

[ame="http://www.youtube.com/watch?v=b2Vcp1La1zE"]620 l20b exhaust tone - YouTube[/ame]

sorry for the shit quality

[rice4life]

Thanks a lot man, If I could, I would give you a hug.

My mom had one of these for like 20 something years, thats why I like 620's.

Have you thought about maybe adding different tail lights? I have wanted to put some DMAX s13 coupe tails on a 620.

[pejsa]

no sir i love the oem tail lights. it had a huge bar rear bumper with trailer light on it, so i 86'd that shit

[JDOGG]

I still have not seen this truck in person but I it is looking great

[metalmonkey47]

Nice little datto you have there sir.


Just some small input,

that long tube won't fit unless you remove the torsion bar first when mounting (trust me I've tried), and on a truck as low as yours, the header collector's gonna get beat to shit against the frame. Go for a shorty. The L20B will actually lose power with a header in stock form. Also, they tend to leaf like a sonovabitch.

For the rear suspension you can use leaf springs off of a 720 4x4 that have a smaller arch. It'll probably maintain the same ride height (or close) with the stock number of leafs over your 620 leafs with some removed. They bolt right in and are about 2'' lower then stock.

Why modify spindle to drop the front end when you have torsion bars? I'm assuming for the disk brakes? Just curious.


keep it up! Sub'd

[rice4life]

If you want more power, look into mating the L20b head to a z24 block.
The 620 already has a lot of the parts needed to do the swap on it.

[pejsa]

Nice little datto you have there sir.


Just some small input,

that long tube won't fit unless you remove the torsion bar first when mounting (trust me I've tried), and on a truck as low as yours, the header collector's gonna get beat to shit against the frame. Go for a shorty. The L20B will actually lose power with a header in stock form. Also, they tend to leaf like a sonovabitch.

For the rear suspension you can use leaf springs off of a 720 4x4 that have a smaller arch. It'll probably maintain the same ride height (or close) with the stock number of leafs over your 620 leafs with some removed. They bolt right in and are about 2'' lower then stock.

Why modify spindle to drop the front end when you have torsion bars? I'm assuming for the disk brakes? Just curious.


keep it up! Sub'd

i went with spindles so i could keep decent geometry in the front while having a massive drop. i have a lot less bump steer and more suspension travel than a torsion drop. and thanks for the info on the headers.........

[pejsa]

and a sorry now to my fellow datsun lovers but i traded the truck last night. wasn't expecting too but it happened.

heres the new hoopty

[244Brick]

nice!!! can you address the paint asap... It's too many 240sx with rattlecan paint

[pejsa]

i work in a body shop so without a doubt it will get painted eventually

[aLaFleur]

Killer man. I can dig it.

[KEVIN.E]

ah shit was gonna comment on the truck and i go to the last page and its gone haha. Been looking for a datsun 521 or 620 forever.

[rice4life]

Cage eet.

[Youngthugga]

I'm so excited to see what you'll do with an s13 after seeing your other truck haha I think this is a good thing.