Tweet
Originally posted by MikeyRa
View Post
-
Already in the works building it right now -
Very nice, just personally finished up my 4g63 build. I love these damn motors.Instagram: @Eurow
Comment
-
Why no JDM VR4 front end? New hood, new headlights and bumper... not sure about the fenders though makes it look WAY more aggressive. Although, I do know that you have other stuff ahead of you such as finishing up your motor and wheels perhaps.
Props, good build. Would love to see more.Hella4 | MTechnica Wheels - Wheel Designer | Memoryfab
Comment
-
They are simple built tough things. Mitsu did a great design on them, I am just improvingOriginally posted by MikeyRa View Post
Because part of my frame is bent. Thus it will have to wait untill I get a new galantOriginally posted by Clun9 View Post
They are Wiseco 10.5:1 1800hd, they are the big boy baddest of the bad pistons IMO. Paid 543 shipped
Also have a few other little updates but not until they are on the carComment
-
This is dope as fuh. I've always had a hard-on for this generation of Galant, hell I may dump one someday as a simple daily. I'd prefer the V6 though, mostly for sound.
You probably know my buddy BJ [I imagine the Galant crowd is pretty tight-knit], he has a 3.8 swapped 5-speed Galant in Utah.- Bagged '98 Chevy S10 - Stock '88 Volvo 240DL - Broken '87 Mitsubishi Starion ESi-R - Also Broken '87 Shelby Lancer #707/800 -Comment
-
Thanks, the v6 are nice but cant beat the evo support on the 4 bangerOriginally posted by Daviticus View Post
Yeah I know BJ he is a great guy. Yeah egokiller is a beast of a car, I watched him pulled a evo 8 it was crazy! He is helping me out with my build giving advice and guidance on where to go.
Speaking of here is a picture of both of our cars when I was out in Utah
Comment
-
Very boss. I know you're only in 'Springs, but it's a good 10+ hour drive, so I can properly say, "Small world". Haha.
Damn you're as low as BJ, I thought he was lower. Isn't he on K-Sports?- Bagged '98 Chevy S10 - Stock '88 Volvo 240DL - Broken '87 Mitsubishi Starion ESi-R - Also Broken '87 Shelby Lancer #707/800 -Comment
-
It is, BJ lives like 2 miles up the road from my cousin. He has come out here a few times, I have been busy each time though.
I am maybe a hair or 2 lower than he is with the new lip. He is on ksport Kontrol Pros I believe.Comment
-
Fresh and clean by mrg7243, on Flickr
Galant-new egr by mrg7243, on Flickr
Rear tie bar by mrg7243, on Flickr
Washed up added a EGR visor(a roof visor) its the only JDM part on my car, put the rear lower tie bar I got for free, and washed her up.Last edited by mrg7243; 01-14-2012, 01:16 PM.Comment
-
8.5lb flywheel for the buildComment
-
Dropped the block and crank off at the machine shop sunday. Waiting right now. Crank is getting cut and magged, block is getting the main studs and then girdle cut. Along with hot tanked and getting magged.
This poster is at the machine shop I love it and want to find one!
..........
........................
.................................................. ............
.................................................. ................................................
and then stripped
The head has 95k on it came from a complete running motor ran me 125 shipped ordered it sunday night got it tuesday. I would have posted sooner but I just figured out how to tether my phone for internet since the house I am living in doesnt get internet till next monday.
And I will leave you off with this
and this
Comment
-
Ah, your thread. Sub'd.
Comment
-
Haha there ya goComment
-
Got this in today, EVO intake manifold paid 87 shipped, also on the back table is a BHM conversion harness
Working on porting it this week, along with the harness installComment
-
Here are the parts that came in.
Fuel rail-evo paid $38
Clutch, I have heard good things about the 6 puck with the upgraded pressure plate. I will see how it is. paid $187
I will get a stock TOBComment
Comment