If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Sarcasm is easily calculated on vortex dude. Take 4 parts GLI lip and divide by BBS RS. If you are left with a remainder, subtract it from omgmoarlow. Profit.
i have a set of staggered 5x100 18" simmons le's, one of the inner lips on the front has a hairline crack and dint on outer lip front. i was going to replace both front outer lip and go wider when refurb. if your interested give me a call 0432657890 $1050
- 2.0 fully rebuilt, along twin 40's Dellorto's.
- 5 speed manual.
- approx lowered 50mm front and rear.
- complete new steering arms, recently wheel aligned as well.
- minimal rust, no structural rust. (can provide detailed images)
- paint is solid and is holding shine, its had 1 re-spray since new.
- BBS RM012 15x8.5 et8 (195/45/15 Nakangs )
- New caster arm rubbers
- Alpine CD player
- 67 XXX on the clock
Interior is in stunning condition, still with its original trim. No cracks in the dash either
Comes with rego till May 2013
Can provide road worthy.
PM me regarding any questions or call me on 0431 728 695
i have a set of staggered 5x100 18" simmons le's, one of the inner lips on the front has a hairline crack and dint on outer lip front. i was going to replace both front outer lip and go wider when refurb. if your interested give me a call 0432657890 $1050
Need the JDM's and same width sorry! Thanks anyway
Engine:
Pauter rods
wiseco pistons +1mm over size
acl race bearings throughout
Arp head studs
Arp rod bolts
Arp main cap bolt
Maruha sump baffle
Maruha head gasket
toda cams
Turbo setup:
custom exhaust manifold
Garret 2871r 0.86 Tial v band housing
Tial 38mm External Wastegate
Custom Steam pipe manifold
3" straight pipe exhaust
Bolt on Diff back 2.5" Exhaust for noise restrictions etc.
custom intercooler piping
Intercooler
custom catch can
Fuel Setup:
id 1000s
Aem Fuel pressure regulator
Walbro 255 lph fuel pump
M-Tuned Dual feed fuel rail
-6 fuel lines from tank to rail
Wheels and suspension:
bc coilovers
24mm front sway bar
Oem Rear sway bar
Boss Frog Fender braces
Poly Bushings throughout control arms
Spherial Jointed lower control arms. Very solid
New ball joints
LE tie rod ends + extended tie rods
Cusco half cage
Wheels:
Work meister 15 x 9 -2
225/45 RS3's
steel wheel nuts
Exterior:
Respray 1 year old including engine bay. (Very straight. few paint chips here and there from track)
Jubiride Flares
Planet miata sideskirts
cut rear bumper
garage vary canards
garage vary lip
Custom Front Splitter Setup with supports
Apr carbon mirrors
Custom Cut bonnet
YSCC Carbon Boot (Rare as fuck)
Rotora 3d carbon gt wing
Custom wing stands and mounts
Custom wing supports
Garage star tow hook
Smoked indicators
Price im looking for is around $26k i suppose.. Will do cheaper without some of the parts etc.. Like Stack dash can be removed, bride, nardi, wheels if you want.
Any interstate buyer will be able to transport this to you.
Located in Brisbane.
This is a solid Track car that can be street driven without all the add ons. Very fun car to drive and a lot of time and money has been put into this to ensure that its extremely safe and reliable.
Comment