Tweet
This car has been my baby for the past half decade. It was garaged for the longest as I pieced it all together for SOWO in 2010. This car has been a lot of fun and has made a couple road trips. Very reliable car and sad to let her go but I must begin the adult phase. House.
**Car is located in Pittsburgh, PA - Moved here for work**
**Reason for selling - Wanting to buy a house**
Will sell without HREs for 28k - must bring own wheels or will arrange for 'affordable set to be put on car'
Will entertain offers or trades + cash.
What you are looking at is a fully built car buy the HorsePower freaks team in Portland, OR. The car was shipped to them and built over a two month period. John Troung was the lead mechanic and has built dozens of well tuned machines. This car is just another testament to quality of work.
No tire kickers. No joy rides.
*Tennessee / Southern Car*
*Never seen northern snow*
2001 BMW e46 M3 HPF 2.75 Build; 704HP - 26 PSI
- Dual tune setup with PUMP & RACE tunes
- Fully Built Motor by John Troung previously at HPF
- Crower rods, Weseco Pistons, Darton Sleeves etc.
- Freshly Rebuilt Head, New valves, springs etc.
- 6k Miles on Build
- 107,227k on chassis - may go up a little as I drive it on weekends
- Manual 6spd transmission with reinforced plate and cage
- Vibra-technic Solid Trans Mount
- Vibra-technic Motor mounts
- UUC Short Shifter with fresh rebuild kit
- Stage 4 HPF Clutch
- DSS 1200hp Chromoly Driveshaft
- DSS 1200hp Chromoly Half Shafts
- AEMv2 Standalone w/ METH Connection(Not connected)
- AEM Guages AFR & Boost
- AEM Traction Control
- AEM Wideband
- Hks BOVS
- Tail 44mm MVR
- PTE 67mm Turbo
- Steedspeed Turbo Manifold
- Walbro intank and Walbro in-line
- All Rear Sub-Frame Reinforcements
- All Sub-Frame Reinforcements
- Front HPF Steel Engine Guard
- Setrab 16-row Oil Cooler behind kidneys w/ -10 AN lines
- Includes spare HPF intercooler - silver not powder coated black.
- Custom HPF 3.5" Exhaust and Open Dump
Body
- '06 LED tails
- ModBargains CSL CF trunk
- ModBargains CSL Bumper
- ModBargains CSL CF Diffuser
Suspension
- New UUC SwayBarbarian Swaybars Front and Rear
- New BC Racing R Coilovers w/ camber plates
- New Control Arms Front
- New RTABs Rear
- New Bushing in Sub-frame
- New Rotors F&R
- New Bearings F&R
Wheels
- HRE 546R
- 19x10 2.5" lip and HRE 19x11.5 3.5" lip
- Stepped lips
- 18" faces
- Will include 1.5" lips if you desire to rebuild to smaller setup
- Custom Built, No Spacers
- 80mm Wheels Studs
*can remove wheels to lower cost but do not have stock wheels.
*Oil Light stayed on before the AEMv2 was aligned properly. Long fixed.
**Car is located in Pittsburgh, PA - Moved here for work**
**Reason for selling - Wanting to buy a house**
Will sell without HREs for 28k - must bring own wheels or will arrange for 'affordable set to be put on car'
Will entertain offers or trades + cash.
What you are looking at is a fully built car buy the HorsePower freaks team in Portland, OR. The car was shipped to them and built over a two month period. John Troung was the lead mechanic and has built dozens of well tuned machines. This car is just another testament to quality of work.
No tire kickers. No joy rides.
*Tennessee / Southern Car*
*Never seen northern snow*
2001 BMW e46 M3 HPF 2.75 Build; 704HP - 26 PSI
- Dual tune setup with PUMP & RACE tunes
- Fully Built Motor by John Troung previously at HPF
- Crower rods, Weseco Pistons, Darton Sleeves etc.
- Freshly Rebuilt Head, New valves, springs etc.
- 6k Miles on Build
- 107,227k on chassis - may go up a little as I drive it on weekends
- Manual 6spd transmission with reinforced plate and cage
- Vibra-technic Solid Trans Mount
- Vibra-technic Motor mounts
- UUC Short Shifter with fresh rebuild kit
- Stage 4 HPF Clutch
- DSS 1200hp Chromoly Driveshaft
- DSS 1200hp Chromoly Half Shafts
- AEMv2 Standalone w/ METH Connection(Not connected)
- AEM Guages AFR & Boost
- AEM Traction Control
- AEM Wideband
- Hks BOVS
- Tail 44mm MVR
- PTE 67mm Turbo
- Steedspeed Turbo Manifold
- Walbro intank and Walbro in-line
- All Rear Sub-Frame Reinforcements
- All Sub-Frame Reinforcements
- Front HPF Steel Engine Guard
- Setrab 16-row Oil Cooler behind kidneys w/ -10 AN lines
- Includes spare HPF intercooler - silver not powder coated black.
- Custom HPF 3.5" Exhaust and Open Dump
Body
- '06 LED tails
- ModBargains CSL CF trunk
- ModBargains CSL Bumper
- ModBargains CSL CF Diffuser
Suspension
- New UUC SwayBarbarian Swaybars Front and Rear
- New BC Racing R Coilovers w/ camber plates
- New Control Arms Front
- New RTABs Rear
- New Bushing in Sub-frame
- New Rotors F&R
- New Bearings F&R
Wheels
- HRE 546R
- 19x10 2.5" lip and HRE 19x11.5 3.5" lip
- Stepped lips
- 18" faces
- Will include 1.5" lips if you desire to rebuild to smaller setup
- Custom Built, No Spacers
- 80mm Wheels Studs
*can remove wheels to lower cost but do not have stock wheels.
*Oil Light stayed on before the AEMv2 was aligned properly. Long fixed.
Comment