Tweet
I know most here are strictly into cars, but I figured I'd post this up here anyway.
I have a 2000 Hayabusa for sale, VIN # JS1GW71A3Y2100116, with a 2002 based Carpenter Race Engines 1397 for sale. I have a clean and clear NY state title in hand. Currently located in Southwest Florida (bike was never re-registered in FL.)
Motor:
2002 Hayabusa Engine w/ Matching Electronics
Carpenter 230 HP 1397 (Big Bore) Package
CP Pistons
Megacycle Cams
Stock Valve Carpenter Head
HD Billet Countershaft Sprocket Cover
Stock Fuel System
Stock Crank
Stock Rods
Brock’s Clutch Mod and Springs
Tsukigi Sidewinder
Koenig 2” Oil Pan
DynoJet PCIIIr with Carpenter Base Tune Loaded
Chassis:
Catalyst Racing Composites Fiberglass Bodywork – Painted House of Kolor Black
Supersport Street Upper
Lowered Stock Rail Tank
Low Profile Front Fender(Removed)
Inner Fairing Panels
+6 Supersport Tail Section
Carbon Seat Pan
Cut 2” GSX-R 1000 Forks
Stock Lower, Vortex Upper Triple Clamp
Vortex Aluminum 50mm, 7 Degree Clip Ons
Magura High End Levers and Master Cylinders
Tiger Racing 24 V Starting and Charging System
MPS Kill Switch
MPS Air Shifter (Bottle, Gauge, and Line Not Mounted)
Hay’s Lollipop Steering Damper
Stock Aluminum Subframe
Re-valved Stock Shock
Straight Link
Schnitz Products Rear Sets
BST Carbon Fiber Wheels (17 x 3.5 Front, 6.25 Rear)
Ceramic Wheel Bearings
Galfer Wave Rotor (Single Front, Rear)
Galfer Braided Stainless Brake and Clutch Lines
Vortex Sprockets (16/43)
Gilles Tooling Titanium Axle Nut
Non-O-ring Chain
Zook 6-9 Over Swingarm
Frame and Swingarm Powder-coated Gloss Black
I am selling the bike as I simply never ride it. Personal circumstances, including health and family, have shifted priorities just after the bike was completed. There are a few small cracks and issues with the glass bodywork, including some large chips/dings on the upper and front fender, and scrapes around the seat mounting area. Bike weighs in at 430 pounds. Never made a pass, less than 1000 street miles. Motor has only seen Motul 300V oil since rebuild. Excellent condition.
Asking $17,000 or best offer. I would be willing to seperate the motor and chassis, or other parts, should the right offer present itself. Please PM with any questions. More pictures to follow.
Older Pic with Fender Installed:
I have a 2000 Hayabusa for sale, VIN # JS1GW71A3Y2100116, with a 2002 based Carpenter Race Engines 1397 for sale. I have a clean and clear NY state title in hand. Currently located in Southwest Florida (bike was never re-registered in FL.)
Motor:
2002 Hayabusa Engine w/ Matching Electronics
Carpenter 230 HP 1397 (Big Bore) Package
CP Pistons
Megacycle Cams
Stock Valve Carpenter Head
HD Billet Countershaft Sprocket Cover
Stock Fuel System
Stock Crank
Stock Rods
Brock’s Clutch Mod and Springs
Tsukigi Sidewinder
Koenig 2” Oil Pan
DynoJet PCIIIr with Carpenter Base Tune Loaded
Chassis:
Catalyst Racing Composites Fiberglass Bodywork – Painted House of Kolor Black
Supersport Street Upper
Lowered Stock Rail Tank
Low Profile Front Fender(Removed)
Inner Fairing Panels
+6 Supersport Tail Section
Carbon Seat Pan
Cut 2” GSX-R 1000 Forks
Stock Lower, Vortex Upper Triple Clamp
Vortex Aluminum 50mm, 7 Degree Clip Ons
Magura High End Levers and Master Cylinders
Tiger Racing 24 V Starting and Charging System
MPS Kill Switch
MPS Air Shifter (Bottle, Gauge, and Line Not Mounted)
Hay’s Lollipop Steering Damper
Stock Aluminum Subframe
Re-valved Stock Shock
Straight Link
Schnitz Products Rear Sets
BST Carbon Fiber Wheels (17 x 3.5 Front, 6.25 Rear)
Ceramic Wheel Bearings
Galfer Wave Rotor (Single Front, Rear)
Galfer Braided Stainless Brake and Clutch Lines
Vortex Sprockets (16/43)
Gilles Tooling Titanium Axle Nut
Non-O-ring Chain
Zook 6-9 Over Swingarm
Frame and Swingarm Powder-coated Gloss Black
I am selling the bike as I simply never ride it. Personal circumstances, including health and family, have shifted priorities just after the bike was completed. There are a few small cracks and issues with the glass bodywork, including some large chips/dings on the upper and front fender, and scrapes around the seat mounting area. Bike weighs in at 430 pounds. Never made a pass, less than 1000 street miles. Motor has only seen Motul 300V oil since rebuild. Excellent condition.
Asking $17,000 or best offer. I would be willing to seperate the motor and chassis, or other parts, should the right offer present itself. Please PM with any questions. More pictures to follow.
Older Pic with Fender Installed:
Comment