.:: Stanceworks - LIKE OR NO LIKE? ::.

[.::M::.]

Cheers,

I have removed literally almost every mod on my car in order to completely redo it over the summer. Wheels/Hood/Trunk/Bumper/Diffuser/Seats/Steering Wheel/Stereo all gone or going and being replaced along with a good deal of bodywork and color change.

I am still currently sorting out which wheels to go with (HRE, Rotiform, CCW, Work, etc)...I posted a photoshop up on M3Forum of the car and was flamed madness for it, apparently to them it looks horrid...I was asked to "go back to my stanced community" lol.

So here I am, and before I finish my car at the end of the summer with the new wheels, I wanted to get everyones opinion on my car if it is to "park" as seen below...I would go down to 19" from 20", 19x13.5 and 19x10.5-11...The wheels in the chop were only used because they were the right angle, and the front fenders will be 1" wider on each side...the poke is more extreme being a photoshop. Stance it or no? :


Show more

[P78]

something is amiss with front bumper imo

but that is brutal

[Anonymoose]

I've always wanted to see a bmw with lots of camber all round so I'm liking the idea but def don't go with the shopped wheels. Less poke up front would look better in my opinion

[.::M::.]

something is amiss with front bumper imo

but that is brutal

Im not very good with photoshop, the front bumper work will match the fender work (gtr open fender), but I didnt capture that very well in photoshop.

I've always wanted to see a bmw with lots of camber all round so I'm liking the idea but def don't go with the shopped wheels. Less poke up front would look better in my opinion

Thanks, the photoshop is a bit extreme, the front fenders will be 1" wider on each side than you see there, and the chopped wheels were only chosen because they were the right angle...I am leaning on rotiform/hre/adv1 wheels. Thanks

[Rírá]

I'm liking the aggressive fitment, another inch on the fenders and smaller wheels and I think you got a winner, if you're going for Roti's the Roc's and MIA's are pretty sweet.

[.::M::.]

I'm liking the aggressive fitment, another inch on the fenders and smaller wheels and I think you got a winner, if you're going for Roti's the Roc's and MIA's are pretty sweet.

Thanks, the chopped wheels had to be similar to 20" to cover the old ones, but will def drop it down to 19" and talking to Roti about the options now, they are the easiest to work with for proper fitment...I will check out the ones you mentioned, their 3 piece race wheels turn me on.

[Jorge]

Rotiform TMBs don't get anywhere near enough limelight as they deserve.

[.::M::.]

Rotiform TMBs don't get anywhere near enough limelight as they deserve.

:drool:

They remind me of the oldschool "euro scene", noted---love em

[Lukey]

do et

[INDOMI]

i think that looks hot! in the photoshop the wheels still look like theyre 20s but 19s would definitely look much better. i say do it man!

[Rírá]

Yea they are great guys, was gonna order a set of ROCs before summer, but shit happened and my money is needed elsewhere.

[Jorge]

I do prefer them with the bonnet badge though, looks like it is missing too much without it.

[Rírá]

that would be sweet on it

[stinkinrich]

Very good 'chop youve done but fitment way too aggressive for my liking.

[.::M::.]

Yeah the roundel stays, front and rear will be the CF roundels...the chop is taken to the extreme with fitment and I shaved the roundel for shiggles. If I go this route with the wheels, I would poke 10MM around, 1" wider front fender, all the shaving will take place for certain (other than the roundel)