Meet Lorelei (1989 325i)

[car_gal_jenni]

here's today's progress:

new lollipops with poly bushings. got the old front rotors taken off, cleaned up the strut tubes a bit, and got the new front rotors, calipers, pads, & wear sensors mounted up.





now i've just gotta do the rear suspension & brakes, and get the correct steel-braided brake lines so i can get that piece all done. the correct outer tie rods will be showing up tomorrow as well. i expect suspension & brakes to be 100% done tomorrow evening

[car_gal_jenni]

love where this is going, great stuff so far.

on a side note, do you think you will have temp issues after deleting oil cooler?

I'm not anticipating any. The motor I got didn't have the bracket for the oil cooler, and it wasn't run in the car it was pulled from & it was fine. If the temp gets a bit high, I can always add it back in. I just didn't want it there for future plans i've got.

[baluzy36]

love where this is going, great stuff so far.

on a side note, do you think you will have temp issues after deleting oil cooler?

[car_gal_jenni]

So! It's been a little while since I've updated this, so I figured I'd give y'all something worthwhile to look at. Boy, have we been busy....!

First off, my front subframe has been welded with reinforcements, sandblasted, and powdercoated. It looks awesome!


Then, we pre-assembled all the goodies prior to getting the motor in the car. Powdercoated and reinforced subframe, z3m power steering rack, 22mm IE sway bar with polyurethane bushings and reinforced mounts, and adjustable sway bar end links.


Speaking of the motor.... I was originally planning on using the 2.5 block with the 885 head, as I had received it. I had the head sent off to be rebuilt, and they WAY overcharged everything, so I abandoned the head. I had another plan already in place at this point. A good friend of mine was pulling his motor out in prep for an S52 swap he's undertaking with his e30, so I snagged his motor. It's the 2.7 block, with a good MLS head gasket, ARP head studs, and the 885 head. Perfect for where I'm heading with my build, eventually!!

We spent the majority of this weekend building out the motor with all the appropriate accessories and brackets and all that bulls-hit. Learned way more about the differences between early model and late model brackets, water pumps, and the like....

But alas!! We got the resurfaced stock flywheel, sachs fx kevlar clutch, and pressure plate mounted to the car. And then we cleaned the transmission....


Before:


After: not perfect, but much much better than before.


With the motor and trans mated together, we got busy getting everything mounted up!





And finally!! Mission success!! Motor, trans, and subframe with goodies are finally in the car!! Gahh it feels amazing to be done with that part of the project!


We still have a LOT to do, but we're definitely making progress. We've gotten a bunch of little stuff done too, like deleting the stock oil cooler, deleting cruise control, and working on mounting up all my audio stuff. Speakers, deck, two amps, and two subs. I had the setup in my orange e30, and LOVED how it sounded. I'm excited to get to hear it in this one!!

[car_gal_jenni]

Well this weekend has been a whirlwind of activity. We did a bunch of work in prep for a new motor going in. As I'm sure a bunch of you know, in order for the motor & trans to come out, the exhaust and drive shaft have to come out. It all came out with relative ease. Except for one minor problem.

The exhaust was rusted out... Let's not forget that the guibo was completely shot.




I'm sure my neighbors that kept driving by thought I was crazy as parts continued to creep all over the yard.



This was the last time that this particular motor sat in this bay.



When I bought the car, the motor ran like absolute dog-s h i t. As we started disconnecting everything in prep for the motor to come out, the draining oil smelled like gas. That gave us a clue as to why the motor was running poorly: we think the rings are blown. Of course, we won't know for 100% certainty until we tear into the motor & do some diagnosing, but it's our only running theory at the moment. It definitely had other symptoms; it was pissing oil everywhere (you can see cooked oil lines down the exhaust in the above photo), and was getting into the intake.



After many angry words, smashed knuckles, and skinned fingers from slipped grips, we finally got this sucker out of the car. Our driveway now needs a good thorough pressure-washing, with all the oil & coolant that kept seeping out of disconnected lines & hoses.




It was a small miracle that this car ran & drove & stopped at all with all the rust, dirt, and grime everywhere. The transmission was straight up disgusting.



At the end of the day, I have an empty engine bay, and a pile of parts that need to be scrapped and a pile of parts that need to be cleaned in prep for new install.

[car_gal_jenni]

So, another major update, minus a giant wall of photos.

I've gotten all new brake components ordered (front & rear new calipers, brackets, rotors, pads, sensors, & stainless steel braided brake lines). I've also put in a healthy order with Ireland Engineering. I've got their 22mm front / 19mm rear sway bar kit with poly bushings, their short shifter kit with the DSSR and all related bushings on order as well. I'm sure the receptionist at my work is going to think I'm crazy in the coming week or so as parts start coming in. *shrugs* oh well!

I've also managed to snag a set of these:



OEM French high beams, legit yellow glass. I am beyond excited to get these mounted up with my smilies and other headlight goodies. I'm hoping to have everything wired up either this or next weekend, weather permitting.

Things are finally starting to button up and come together!!

[car_gal_jenni]

So, I haven't updated the thread in quite some time, so I apologize in advanced for the wall of text/photos, but I figured I'd share all the progress that's been happening to my dear Lorelei in recent times.

So the interior has been completely gutted.




I've fixed the driver side floor pan rust with POR15


I've completely torn down the motor, and gotten the head to the machine shop. I'll be taking the block there as well as soon as I get some time. Needless to say, this motor is in definite need of a good thorough cleaning, which it will be getting.





I've also gotten all of the previous suspension crap taken off the car as well. While pulling the previous owner's Ground Control coils, I noticed that I need to replace just about everything else suspension-related under the car. Every bushing is shot and/or rusted, so I'll be replacing inner/outer tie rods, ball joints, front/rear sway bar end links, sway bar bushings, new H&R sway bars front & rear, rotors, calipers, ... everything.


I've finally got my HVAC control unit replaced, since the light cables were busted in the previous one. Got the 13-button OBC mounted & the harness run. I've also gotten her waxed pretty well, too. With everything that's been going on with the car, I just have to look at pretty pictures to remind myself that I'm doing her right by tearing everything off LOL.


I even managed to snag a couple of goodies as extras too


Needless to say, it's been a busy month (give or take), and I am nowhere near done. Things are slowly starting to come back together, but the more I do, the more I come to realize that it needs my attention.

[car_gal_jenni]

i'll get more photos as i get her put back together. right now, she's pretty torn apart on the inside as i work her over. i'm going over the wiring & making sure that everything is functioning properly before i start adding & changing things.

i've got the busted up 6-button obc wiring pulled in prep for the 13-button obc that i'll be putting in. i've gotta swap out the turn signal stalk with the obc stalk, and the wiper stalk for the ICS wiper stalk. i have to run the heated seat harness after i make sure the floor pans are all rust-free & painted or POR15'ed. i still have to get the sound system put back in & the door cards swapped out.

lots to do! haha

[OEM+ sluts]

Very nice, more pictures!

[car_gal_jenni]

Well, I finally got a new e30 to replaced my totaled one (I miss it! :cry: ) I figured I'd introduce the community to my new lady.

Everyone, meet Lorelei.




She currently sits on bottlecap wheels (which will eventually change as money comes up) and ground control coilovers (which ride less than comfortably, so I'm changing them out for some H&R springs and Bilstein shocks as money comes up). The red seat has already been evicted and returned back to the previous owner (part of the agreement of purchase, which is totally fine by me) to be temporarily replaced by some dark grey heated comfort seats (which will eventually be replaced for some heated houndstooth sports, as money comes up to get them reupholstered).

I'm excited to get a fresh start with this car, and am already knee-deep in projects on her.

I pulled a really poorly installed keyless entry/alarm system and fixed up all the wiring from that fiasco, and am in the process of sorting out some surface rust in the driver's floor pan with POR15. I'm also rebuilding a secondary m20 motor, since the one she came with was blown when I bought her. She's far from done, but I'm taking very good care of her!