My Hellastock EK/EJ6 98 Hatch from idaho

[blakeb]

Did a test fit the other day I think it went good lol

[blakeb]

anyone think it be possible to Flip faces? like use my inner barrel as an outter? i thought bout doing that and polishing em real nice.

[blakeb]

any certain brand or look you're planning on going for?

Work makes em I found 3" lips on wheel flip but that's the smallest I've seen.

[AKToyotaluv]

Well I'm on the hunt for 36 hole 2" lips and I can't find em but I find 3" lips all day long so idk

any certain brand or look you're planning on going for?

[blakeb]

Well I'm on the hunt for 36 hole 2" lips and I can't find em but I find 3" lips all day long so idk

[AKToyotaluv]

as long as you adjust up. lolol. nahh, possibly

[blakeb]

Anyone think it will possibly to fit a 17x9 and still get low on a ek hatch

[blakeb]

Lol it doesn't look that crazy lol. At least you have the juevos to drive as low as you are straight snow. Props bro.

we had a good 5-6 inches then whatever got blown around. haha yeah its been tough

yeah that winter storm thing fucking sucked here in ontario. buffalo got pretty fucked up, too.

we were on the very edge of it we didnt get it horrible but we dont usually get snow here till december. its been more than a week and we still have snow and ice in even the areas that see traffic most haha.


glad i dont drive my car during this, i did one winter and never ever ever again

yeah im gonna try and buy some cheap 4x4 pickup for work so i can give this car alittle break. dont need anything fancy. ha

love your car always loved the hatches I cut 2inches out of a set of knuckles for my buddy once but he was aired. as long as you your a good welder I say go for it. the trick for welding cast is to heat it up before you weld it make it glow then lay your bead then cool it down slowly worked great for his car drove it across country twice never had any issues

we got a good minitruck guy out here in the area. he does and has built alot of fab stuff and its all held up. might possibly have em do my rear tubs so i can fit anything i want in the future as well. i was told 2 inches on the knuckles cut and reweld would give me what i want. plus lowering forks as well then i can raise my suspension and still have that sexy drop with all the nice shock travel. it sucks driving bottomed out like i am now. Im taking off the racing harts and rocking steelies for rest of winter cause i want to start saving and ordering up everything.

[E30NH]

love your car always loved the hatches I cut 2inches out of a set of knuckles for my buddy once but he was aired. as long as you your a good welder I say go for it. the trick for welding cast is to heat it up before you weld it make it glow then lay your bead then cool it down slowly worked great for his car drove it across country twice never had any issues

[Devocat]

yeah that winter storm thing fucking sucked here in ontario. buffalo got pretty fucked up, too.


glad i dont drive my car during this, i did one winter and never ever ever again

[AKToyotaluv]

Lol it doesn't look that crazy lol. At least you have the juevos to drive as low as you are straight snow. Props bro.

[blakeb]

https://vimeo.com/112352562

This arctic blast that hit us here in idaho has taken a toll on me haha.

[blakeb]

Question for the fabrication dudes. I want to cut my knuckles 2" how hard would that be??

[blakeb]

spotted you the other day! looks clean asf. Keep it up man. Cant wait for the new lips!

Where did you see me? Thanks man. I want to fix my quarter panels bad I found these pretty cheap



I didnt know 6th and 7th gen hatches had compatible QPs

[Sebastianglenn]

spotted you the other day! looks clean asf. Keep it up man. Cant wait for the new lips!