Wide Works S13

[Junya]

this is awesome! can you provide more input on how you are making your own flushmount spoiler? the materials and diy perhaps?

ive been itching to put a flushmount on my car but i dont know where to start. maybe you can kickstart my brain

EDIT: just saw the first couple of posts... Plasticine! thanks so much!

[forgotten]

4 mounts later not a lot have change

I got a type-x areo kit (Bumper and Side skirts)


Adjusted the ride height camber/toe/caster (still needs to be aligned professionally)






Test fitted the bumper


Bleaded the brakes


Cold Canadian winter and a lot of snow arrived!
My daily 97 Volvo 850!




So this winter i needed to work on the car, so i searched and haven't found no place to store and still work on it at a reasonable price. I stored it at home, at first as you can see it was pretty bad getting around the car!




Made some room in the garage and received the last missing aero part :bow:


Pretty hard to explain what i did with the wiring so i made this paint drawing to explain




I made a hole and fitted/hidden the harness
Engine bay


Inside car


Wiring almost done (still looks like a headache)


Motor, still needs the piping's to be done in one piece and some black powder coat on some parts


S13 fuel filter, i installed it under the car but pictures were 2 dark, i will try again later


I am also working on a is300/altezza Ducktail Wing

[rsingh3g]

^^ most likely a spammer

[forgotten]

I'm looking forward to using this .

pics did not work !

[scweet14]

dear lord how have i not found this build before?! you sir are a fucking boss! love all the custom work and custom fenders.

im glued now, so finish it

[forgotten]

it should look better with some camber

[SD202]

love how it sits on the works ggot damn

[axelillo_PR]

That eg is pretty dope, also dat ass :O

[hi its me alec]

Wow, awesome work. Everything looks great so far, especially the Works

[forgotten]

Over the last couple of week, I didn't have a lot of time to spend on the 180sx because I was working full time. I also had to give some love to my sir eg6; the clutch was broken and the engine had over 180 000 miles. I decided to buy a civic type-R engine

Last drive before removing the sir, FYI the gtr is my friend's car



Sir


How the type-r arrived from Japan (not mine by the way - just another one waiting for a home)


The type-r I bought


Sir out


Empty engine bay


Almost done


I have been told by plenty of person that the swap wouldn’t take me any longer than two days... I ended up spending two weeks because of all the things that didn’t fit properly and the tons of details that I didn’t know about.


Now for the 180sx
I took some pictures with the overfenders, still no alignment












I have installed the rear coilovers


front coilovers, exterior tirods, samco hoses, walbro gas pump


put some colors in the trunk


I installed the pump with new gas tank gasket, but I forgot to take pictures


I had to change the s13 inner tirods for the 300zx inner tirods in order so fit the SPL ones


How the engine bay looks like


Front coilovers installed


Starting to have some light !




Lights didn't close so I searched 'til I found this ... I tried with a silvia controller and it works well, but my pop ups just don't lift. Then I noticed that the controller from the180 had 2 plugs and the silvia only one, so that might be the problem.

[Stuster]

So wide ass I want a s13 so badly !!

[forgotten]

Went to New York Zoo


Rpm Nyc


Didn't came empty handed


Finally got my greddy type s coilovers after 6 monts of waiting and some spl tie rods


Little setup


I had a left hand drive engen bay wiring that was already wire tucked and didn't fit in the right hand drive chassis so i had to find one that fits, after 2 weeks of intense searching i got one installed it and now the s14 sr20 works in the rhd s13, here is the rhd wiring so much wanted ready for wire tuck


Interior for now


Found a clean battery box


Wide Works Decals if someone want some just mp me

[Hitman Cody2130]

Subbed, sweet build so far

[forgotten]

Finally a update! Btw 501st like on you fb OH YEAH haha

Thanks its one at the time

great build moar work post3d please

il try to do the more i can

[96CD7]

great build moar work post3d please