BN Sports Blister Kitted RX7 (Daily)

[Pyropiggy2.5]

Beautiful!

Holy crap the fitment looks like a pain in the ass though.

It looks like it's purely fiberglass? Or some kind of polyeurethane?

[Kruizer]

Beautiful!

Holy crap the fitment looks like a pain in the ass though.

It looks like it's purely fiberglass? Or some kind of polyeurethane?

All fibreglass, ah I'll fix it

[rsingh3g]

Swapping a RB in this rx? lol

[mad-ass]

I have a very good feeling about this one.

keep up the good work!

[rice4life]

Like posted before, is it an authentic BN sports kit?
Doesn't matter if it is or not, because if you plan on going low it is going to be inevitably damaged.

Looks good so far, it would be painful to cut into the FD's body like that, even if it was necessary. Then again FD's are probably cheaper where you live compared to the states.

[Kruizer]

Swapping a RB in this rx? lol

I have a very good feeling about this one.

keep up the good work!

Like posted before, is it an authentic BN sports kit?
Doesn't matter if it is or not, because if you plan on going low it is going to be inevitably damaged.

Looks good so far, it would be painful to cut into the FD's body like that, even if it was necessary. Then again FD's are probably cheaper where you live compared to the states.

FD's can be bought for smarties here dude...

Well I have been up the walls with work the past few weeks but I have a little update, I finally bought an engine for this pony, I decided to stay with what I know, Nissan. The new power plant is a forged RB25, spec below :

RB25DET Spec 1
Head Polished with Gasket Matched (Westward Precision Engineering)
HKS Camshafts : Intake 254 / Exhaust 264 (Spec’d By Garage D)
New Mahle Forged Pistons (1mm Oversized)
New Eagle H Beam Rods
RB25 Crank Balanced (Westward Precision Engineering)
New ARP Head Studs
New Spool Head Drain Kit
New ACL Race Bearings
New Nissan Full Gasket Set
New Metal head gasket
New Nissan Belt Set
New Nissan N1 Oil Pump
New Nissan Water Pump
Anodised Blue Lightweight Pulleys
New Nismo Low Temperature Thermostat
Garrett GT3037 Turbo Dynamic’s (Turbo Dynamic’s)
Japspeed Manifold
Metal Exhaust Gasket (Summit Racing)
Custom Downpipe
Z32 AFM (Japanese Performance)
Nistune RB20DET ECU
New Crank Case Breather Kit
SARD 280LPH Fuel Pump (Japanese Performance)
New Fuel Filter
Turbo Blanket (Turbo Dynamic’s)
Custom Intake Pipe
RB25 Gearbox
Custom Prop-shaft
HKS Twin Plate Clutch

In the car :


On its way up to Gripfab


I want to change the injectors from 550cc to something a bit higher and replace the standard intake manifold, have it looking more like the engine below :


The aim is for a comfortable 500bhp without pushing the engine too hard.

[rsingh3g]

Damn, how did I konw this would get an RB lol

[DragginWagon]

i dont think i could ever cut into an FD. lol. but it will be so worth it. fitment is nuts. i would tape pillows to the sides of the garage just incase haha.

[scweet14]

^

damn dude its been months since updates and all you have done is get an engine?!?! haha anything else?

[slwrthnu]

i dont think i could ever cut into an FD. lol. but it will be so worth it. fitment is nuts. i would tape pillows to the sides of the garage just incase haha.

remember it's just a car. i'm going to cut into mine and then see how close i can get to walls with it.

[Stupid Kid]

^

damn dude its been months since updates and all you have done is get an engine?!?! haha anything else?

Only an engine lol

[Kruizer]

Damn, how did I konw this would get an RB lol

Cause I'm predictable or your awesome, I'm going with your awesome :p

i dont think i could ever cut into an FD. lol. but it will be so worth it. fitment is nuts. i would tape pillows to the sides of the garage just incase haha.

I cut into a Veyron if it was in front of me...

^

damn dude its been months since updates and all you have done is get an engine?!?! haha anything else?

Yes but an engine with that spec is worth waiting for

remember it's just a car. i'm going to cut into mine and then see how close i can get to walls with it.

Like your style ^^^^

Only an engine lol

Gonna keep it modest and run 500bhp on pump gas 95RON.

So I offered up some Racing Harts I had out in the shed, 18 x 10JJ and with a 50mm spacer I think they'll be minty

[cardoza]

So I offered up some Racing Harts I had out in the shed, 18 x 10JJ and with a 50mm spacer I think they'll be minty

Can't say that I've ever understood the point of going widebody then running spacers. You should get some low offset wheels with a big lip, like those Meisters, and do that kit some justice IMO.

[scweet14]

agreed^^ trade the racing harts for something wider

[rsingh3g]

I try to be awesome, but until I can build something as capable as this I will not be as awesome as you.