Atom's 2 door Amazon wagon Project:Headquarters

[Atom]

Please tell me more was holding that car up than a Jeep wheel and a donut spare? Dsh looks awesome already

I mean, it’s Pick n Pull. That’s kinda the deal.

[Quillhill36]

Please tell me more was holding that car up than a Jeep wheel and a donut spare? Dsh looks awesome already

[Atom]

Since Pick N Pull is have 40% off for members this weekend, I went back and grabbed the oil pan off of that 960. Man, Volvo really wanted to be sure it stayed attached. Sooo many bolts! This is the only RWD configuration for the “whiteblock” (modular) Volvo engine, so typical usage is to section a chunk out of the middle (since this is a six cylinder) to use for 5 cylinder RWD swaps. I’ll probably need to make an ARC Asylum style crossmember to clear the rear sump.



I’m not entirely sure which pan configuration will work for me, or even if this pan will work on an RNC block, but I figured better safe than sorry.

[Atom]

Some powder coating and concept work.

Adding brass cap nuts to accent the cam cover bolts



Ran a pipe tap down the PCV nipple to add a flare adapter to copper pipe. Waiting on a spring bender to show up before I route it.



Single stage “chrome” powdercoat on the lower intake

[Atom]

Some more dash work. I didn’t place the ribs exactly right (protrusion wise), but it’ll be good enough. I plan on adding a “chrome” (polished aluminum) strip between the top and bottom half. Black top, red bottom.

Reference:





Now for the foam



And roughed to shape



Next I’ll resin coat it to make it a bit more rigid, then start filling.

[Atom]

I love all the drawings and sheit (giant mdf caliper got me LOLin') but if I said I understood wtf are you trying to discover I'd be the biggest liar

Stay tuned

[Fruttolo]

I love all the drawings and sheit (giant mdf caliper got me LOLin') but if I said I understood wtf are you trying to discover I'd be the biggest liar

[Atom]

Hmmm, all the measurements and technical info looks great but have you tried just smushing them together?

I usually wait until all the measurement shenanigans don’t work. Then I smoosh

[MikeyRa]

Hmmm, all the measurements and technical info looks great but have you tried just smushing them together?

[Atom]

Always love getting a box-full-o-parts!

[Atom]

Took some time this morning and on lunch to take measurements as best I can. The depth measurements are accurate. The inner surface of the two bellhousings are just “best I can” measurements. I scribed every inch going in (then two more at half inch in the Getrag).



Then I broke out the trust old “large scale” MDF calipers



Took a bunch of measurements



Converted the measurements to 2D CAD



Overlaid the two



Looks like the M20 throw out bearing contact surface will line right up with the B5254T clutch fingers.



I won’t be able to set final depth until the clutch slave cylinder shows up to measure resting depth. If my math/understanding is right, if I put a spacer between the flywheel and pressure plate that is the thickness of the clutch disk minus frictions (at least to the rivets) than tighten the pressure plate down, the finger height should be the maximum “stack height” and should be where the throw out bearing surface rest depth is. Correct? (Does that even make sense)

[Miroteknik]

been wanting to get into fiberglass/epoxy/resin work for a while, watching this is great

[Atom]

A little more dash work. Trimmed down the interface plates, added spacers to accommodate upholstery materials and a bit of air so they don’t squeak or anything.



Regular resin



Add thixotropic



More work tomorrow before work maybe

[Atom]

Mock up front clip thanks to My local BMW parts guy! Get this propped up and use it to mock up all the components for the swap ahead of time to ease the swap into the Amazon.

[Atom]

Dash fiberglass with a rough trim.