Primered Lady (CB7) Picture Heavy!

[projektzwo]

yep, lower and wider must be this CB7...

[P78]

i like the new wheels, but now you'll need to go lower

[244Brick]

Good to see it back to normal.. swew winter sux.... Time to get a smaller lip, stiffer springs, and go lower :p

[brsteinbach]

Put my wheels on yesterday, I need a dslr so I can take some better pics especially at night, I tried to take some last night with my point and shoot and they came out way to blurry even with a tripod, enough talking on with the pics...


Wheels-1 by brsteinbach, on Flickr


Wheels-2 by brsteinbach, on Flickr


Steelies by brsteinbach, on Flickr


Steelies-1 by brsteinbach, on Flickr


Jacking points with steelies by brsteinbach, on Flickr


Steelies height vs Wheels by brsteinbach, on Flickr


One wheel on by brsteinbach, on Flickr


One wheel on-1 by brsteinbach, on Flickr


Wheels at full droop by brsteinbach, on Flickr


Rear wheel poke w full droop by brsteinbach, on Flickr


Front wheel poke at full droop by brsteinbach, on Flickr


Wheels on in the air by brsteinbach, on Flickr


Wheels on drivers side by brsteinbach, on Flickr


Front shot with wheels by brsteinbach, on Flickr


Side shot w wheels by brsteinbach, on Flickr


Front pinch weld by brsteinbach, on Flickr

I didn't touch the suspension height, just put the wheels on, also I didn't drive so it probably went down another 1/4".^


Fitment right after put on by brsteinbach, on Flickr


Fitment right after put on side by brsteinbach, on Flickr

Thanks for looking everybody. Feels good to be low again and have my wheels on, I know its still pretty high but after 4 months of driving at 5" jacking points 3" is pretty low especially when my down pipe, oil pan, and trans sits .5" lower then the pinch welds.

[brsteinbach]

Is it to late on that vote. Since wisconsin is a one plate state id use that to my advantage and not run one. ..Plus the dairyland plate is not the coolest one out there and its blocking the jdm goodness. Just a thought.

I'm pretty sure we're a two plate state cause they give us two plates and my friend just got pulled over last night for no front plate I'd love to not run it, I just **** being hassled by the cops.

But thank you.

I do my very best not to look in here because it makes me miss my old car dearly.

Keep it up, you're doing it right.

Thanks man, I'll have way more updates and pictures when it warms up some and the salt is all off the roads so I can put my wheels on.

[HooWybrow]

I do my very best not to look in here because it makes me miss my old car dearly.

Keep it up, you're doing it right.

[tunnelvision]

Is it to late on that vote. Since wisconsin is a one plate state id use that to my advantage and not run one. ..Plus the dairyland plate is not the coolest one out there and its blocking the jdm goodness. Just a thought.

[brsteinbach]

You do that dew.

I do, do that dew sometimes.

Good progress and I can't wait to see updates. Paint!!

Paint this spring!!!!

[dgoizo]

Good progress and I can't wait to see updates. Paint!!

[Isuzupickup]

You do that dew.

[brsteinbach]

Gotta have the car wash pictures!

















I can not wait for warm weather! I wanna lower my car again and put my wheels back on soooo bad!

[brsteinbach]

Well here's a crappy test video for all of ya'll. The mount wasn't as tight as it should have been so I'll be making a new video soon. Be sure to watch it in HD!!! Also let me know what you think.


[ame="http://www.youtube.com/watch?v=kQ2XmpDVTi0"]http://www.youtube.com/watch?v=kQ2XmpDVTi0[/ame]

[244Brick]

Ok sweet post it once you get something

[brsteinbach]

Looks great.. i would round those edges tho... o how is it when recording any bouncing?

Thanks, I filed them so there not super sharp but I am going to round them. It's a little bouncy and has some vibration. I am going to get a video today, hopefully all goes well cause I tried to take one last night and the damn audio was out of sync.

[244Brick]

Looks great.. i would round those edges tho... o how is it when recording any bouncing?