633csi - e24 slow progress thread.

[DeleriousZ]

I'd never really paid much attention to these in the past, but looking at them now, the body lines on em are absolutely perfect for what the car is. Time to hit up the classifieds lol.

[FREExSPIRIT]

Diggin the wheels !

[DinanDave]

^^^ agreed ^^^ love it doe E24 mmmm

[dav3design]

Ah man those wheels are perfect! Needs more low then the whole thing would be perfect!

[willis]

Looks the best in it's current state. That's sketch about the wheel. I'm only running 4 bolts on one of my corners because one of my studs stripped out. Maybe I should fix that....

[SheaMoose]

Looks really good!
I've always wanted an e24.
It still needs more low

[evilstar]

Got a new project car so this is getting put on hold for a little while. Doing a full strip down and color change so that requires all my attention for now.

♥ Raf

[evilstar]

here are the rest of the pics.


e24 mesh 8-12 -14 by MyEvilStar, on Flickr


e24 mesh 8-12 -13 by MyEvilStar, on Flickr


e24 mesh 8-12 -12 by MyEvilStar, on Flickr


e24 mesh 8-12 -10 by MyEvilStar, on Flickr


e24 mesh 8-12 -8 by MyEvilStar, on Flickr


e24 mesh 8-12 -7 by MyEvilStar, on Flickr


e24 mesh 8-12 -6 by MyEvilStar, on Flickr


e24 mesh 8-12 -5 by MyEvilStar, on Flickr


e24 mesh 8-12 -4 by MyEvilStar, on Flickr


e24 mesh 8-12 -3 by MyEvilStar, on Flickr


e24 mesh 8-12 -1 by MyEvilStar, on Flickr

[evilstar]

here is one but its late so ill post the rest tomorrow

[evilstar]

Late night photo expedition. Photos in a few.

♥ Raf

[evilstar]

Proper Photoshoot coming soon.
♥ Raf

[indyz12]

Did the wheel fall off because it wasnt bolted tight enough?
I had a similar experience with a rear tyre - although the wheel was torqued up, it only had 4 bolts of 5, was out of balence, and snapped a bolt. Didnt quite fall off but almost did, was scary as hell.

Well, moral of story, use good bolts and torque them up TIGHT. These cars are heavier than you think.
Good luck with the project.
Get some BBS rims on there!

[evilstar]

Take a mallet and a heat gun to that and it will look like new

My friend ruined a set of rikens(optional FC wheels) by what he claimed to have been running over a "good sized" rock. I got the wheel and heated it up with a heat gun and smashed it back about 3" on one side and 1" on the other.

It looked like shit without a restoration, but for a ghetto fab job it held air.

I have both a mallet and a heat gun. So I will give it a shot for shits and giggles but don't have high expecations. lol

Wow, how did You manage to rip the wheel of like that?

Wheel came off on the freeway en route to Avila. Another car ended up running it over thankfully no one was injured.

sucks

loved it on those wheels

Have another set lined up for Thursday. I think they will be well received.




I am selling the enkeis if anyone is interested feel free to make offers. 15x8.5 et-20 sandwich mounted 3piece. 5x120 not sure of the CB but larger than 72.6 Selling parts or whole set depending on offers.

[MartinsElerts]

Wow, how did You manage to rip the wheel of like that?

[P78]

sucks

loved it on those wheels