Bagging my 07 Impreza 2.5i Wagon

[CubbyChowder]

This turned out awesome man! Fitment looks really good. Flush as flush can be.

I have one suggestion for you. AccuAir recommends that you place the water trap between the tank and VU4 due to the fact that most of the condensation happens inside of the tank. The air is pretty warm from the compressor as it enters the tank. The air expands and cools down inside of the tank, which is when condensation occurs. Although placing it between the compressor and tank is still somewhat effective, it's a better idea to place it between the tank and valve. That way you are confident that clean, filtered air is entering your valve. Even the smallest debris in your valve could cause a slow leak, and then you'd have to take it all apart and clean it. It just makes for a more hassle-free experience down the road.

Other than that, awesome write-up! Very informative and detailed and shows how DIYable this process really is.

[johnrocs]

yeeee buddy....stance showroom feature you say??

Haha thanks Taylor - I dunno, need to get some NUE's on there first Soon!!

Looks awesome! I love it.

Thank you Katie! Love your Suby too!! Good luck in the All Ladies Top Scoob!!! (for a great cause I might add) You have my vote!

[KatieO]

Looks awesome! I love it.

[tstacks]

yeeee buddy....stance showroom feature you say??

[johnrocs]

Finally an update!

Hey all! So I finally got my server back up and running, turned out to be a lot more work than I expected. I restored everything from backup so the images should be working again. In other news, our good friend Cyrus was able to do the tubbing up front which turned out great! For those that were interested, here are some before and after shots.

Before the Tubbing

You can see in these shots where the main problem spots are. I did a lot of preset 1 cruising down at H2Oi




After Tubbing
Cyrus basically just chopped out the top of the wheelwell and welded in a 1.5" tall "spacer" to the bottom, the same idea as raising strut towers. Without modding the fusebox that's about as high as we could go.

A top-down view of the driver side - sorry I forgot to start taking pictures before putting the fusebox back in...


Tried to get my Droid in there...


Closeup


Underneath...


The passenger side was a lot easier - here's a top down shot


A bit closer - this shot gives a good idea of how much height was added


Underneath


Results!


Here's a closer look of the post-tubbing fitment in the front. Also... Kevin cracked a barrel down at H2Oi (seemed to be a theme this year) - he's been rocking one of Will's 17x10 RS's as a donut on his RS (yo dawg yo... ) - BTW, who let that unbagged Suby in our driveway?!


Another shot...


Fall is in full swing here in Vermont and the colors are absolutely beautiful. Sometime in the next week or so we plan on doing a little photoshoot, so look for that in the stance showroom!

Side note... my next goal.
With the tubbing done, I have my eyes set on laying subframe - I'm a little over 1/2 inch away when dumped. With my current camber setup in the front, the bottom plate of the bag is sitting in the stretch of the tire. I think if I add more negative camber to the plates and add an equal amount of positive camber to the bolts I should clear up enough room to thread my struts up a bit further. In addition to that, I'm going to top-mount the camber plates in the front. I think with the combination of threading + top mounting, I should get enough drop to hit the ground! Hopefully the wheel will tuck in the fender as the car lowers... it's gonna be close! I really love my fitment right now, but I'm so close to laying subframe I just have to see if I can do it


Thanks so much to everyone that followed this thread and all the kind and encouraging words along the way. There aren't enough words to describe the awesome vibe and incredible community around here. Thanks to the Stance Works crew for providing such a wonderful place for enthusiasts to meet and share their passion.

THANK YOU
Bag Riders
Will Fisher (Will@BagRiders)
Alex 'Rali' Kepchar (Rali@BagRiders)
Kevin McGovern (SubieRuby / Kevin@BagRiders)
Taylor Menezes (tstacks)
Cyrus House
Brett Hudson

[johnrocs]

Sick shot John!! Can you send me a high res version?

Thanks dudeman! I'm adding a few to the NAS right now

[Will@BagRiders]

Sick shot John!! Can you send me a high res version?

[johnrocs]

Hey everyone, I was down at H2Oi this weekend with the rest of the Bag Riders crew. We had an awesome time, it was great to reconnect with our show buddies and it was awesome meeting so many new people! Thanks to everyone that stopped by the booth!

It appears my server is still down, so I'll try to fix that tonight so the images will be fixed. Looking forward to getting tubbing done up front (pics will be included, should be happening on Thursday) and then getting some new shots with proper fitment!

This I like

Thank you!

updatessssssssssss

Should be getting tubbing done on Thursday, might be slapping some Rotiforms NUE's on there in the very near future but I'll post up more shots once the tubbing is done. Need to get that fitment in the front the same as the rear! Here's how she sits now...

Nice meeting you this weekend dude.

You too man!

[OSSHWA]

Nice meeting you this weekend dude.

[C.Johnston]

updatessssssssssss

[Corsacruizer]

This I like

[Fastphil]

nice!

[johnrocs]

please make sure you take pics of the tubbing process if you can <3

Will do! You can sort of see the lines I drew in the wheel wells showing where I plan on cutting, but I'll be sure to take some shots of the actual process... and the results

[C.Johnston]

please make sure you take pics of the tubbing process if you can <3

[johnrocs]

Looks awesome man! Great build!

Thanks! More shots soon. Gonna have tubbing done tomorrow so should be quite a bit lower.

Here's a shot from yesterday...