OZ Futura lips nad barrels sizes.

[Crankey]

are those wheels sandwich mounted ? looks like alot of area on the center to fit the barrel behind the lip, with the center fitted in from behind. then the center would be more flush with the lip.

and as to what size a lip is, if it's .5 inch from the bead where the tire sits to the bolting surface, I call it a 1/2" lip. that is the conversion I used to identify lips before and it seems to be true.

best thing to do is take em apart and then measure them...they need a refinish anyway.

[JeyJey]

Can you help telling me the measures of the centres caps?

diameter of the logo base and height such as the diameter of the hole screw?

Thank you

[projektzwo]

Sounds like they are 1.5inch lips and 7inch barrels then. depending on the back pad.

well, today i measured the inner barrel and it was 18,5cm...

[Chris@fifteen52]

1" lips .5" face and 6" barrel for 7.5" wheel

[Zic]

Sounds like they are 1.5inch lips and 7inch barrels then. depending on the back pad.

[projektzwo]

If they are reverse mounted, they should be 1,75inch lip and 6,75inch barrel.

are you sure, because the wheels are reverse mounted but i measure the barrel and it's over 18cm, which means 7inch...

probably the barrel is around 19cm, as the lip sits just like this, the only one difference here is that the wheels are not sandwich:

[Zic]

they're ET30

If they are reverse mounted, they should be 1,75inch lip and 6,75inch barrel.

[lowrider]

may i have some clarifications on the part with the subdivisions please, thank u

[da_joint]

well u may find it useful if u wanna calculate a 1,5 " lip or a 1,75" lip.

[projektzwo]

1 inch= 2,54 cm
and subdivisions are
0 1/8 1/4 3/8 1/2 5/8 3/4 7/8 1

yeah i know that 1 inch = 2,54 cm

but didn't get the point with the "subdivisions"...

[da_joint]

thanks for the link, but i'm still not quite sure, because don't have measuring tool in inches, only in centimeters and i can figure out the exact numbers...

but most probably its a 7,5inch barrel with 1,0inch lip, as they're with rear mounted faces (not sandwich).

1 inch= 2,54 cm
and subdivisions are
0 1/8 1/4 3/8 1/2 5/8 3/4 7/8 1

[projektzwo]

That's a 5" barrel, 1" lip and the center are 1" thick (sandwich mounted result 7" )

@projektzwo -follow the link

http://www.wheel-whores.com/forum/viewtopic.php?t=2795

thanks for the link, but i'm still not quite sure, because don't have measuring tool in inches, only in centimeters and i can figure out the exact numbers...

but most probably its a 7,5inch barrel with 1,0inch lip, as they're with rear mounted faces (not sandwich).

[da_joint]

That's a 5" barrel, 1" lip and the center are 1" thick (sandwich mounted result 7" )

@projektzwo -follow the link

http://www.wheel-whores.com/forum/viewtopic.php?t=2795

[projektzwo]

I know the 8.5's pretty well, what et are they?

they're ET30

[Oh, Word?]

Was just going to make a question thread but seeing as how this is up I'll ask in here. 17x8.5 and 10 OZ Pegasus both +45. There rear mounted stock so if I sandwich mount them I know they'll be a half inch wider but what happens to the et? Im mostly confused because its an even amount both positive and negative.