I've been posting up in the Builds section quite a bit the past few days, figured I'd come and say hello seeing as I'm in good old blighty and have been to a few of the meets in MK.
This is my Touring - it used to be on bronze Rotas, but I put E34 M5 Contours on it last week, and it looks much better now! I usually think people writing out a full spec is a little bit ghey, but here goes anyway:
'99 E36 323i Sport Touring
Engine:
2.5-litre straight-six
aFe induction kit
Fox cat-back exhaust
Evosport power pulleys
Traction control removed
Chassis:
Spax RSX coilovers
RPM camber/castor-adjustable front topmounts
Rogue Engineering rear topmounts
Eibach anti-roll bars (though rear not installed yet, I broke a bracket so I have no ARB)
Eibach/SPC adjustable rear camber arms
Powerflex polybushes
Meyle Heavy Duty front lower arms and ball joints
Meyle Heavy Duty front ARB droplinks
TAR-OX G88 discs and Strada pads all round
Wheels/tyres:
8.5x17 ET13 (front) and 10x17 ET15 (rear) Contours, silver centres with diamond cut dishes.
195/45 and 215/40 Falken Ziex ZE912s.
Exterior:
M3 Evo splitter
M3 rear valance
Roof bars removed and carbon roof wrap
Lamin-X tint film on indicators and fogs
6000k HIDs
Matte black headlight shrouds,
323 badge removed
Kidneys painted black
US spec numberplate blank strip (not fitted in most pics)
Arches rolled & pulled
Interior:
Momo steering wheel
Alcantara gaiters with ///M stitching
E46 Clubsport gearknob
Flocked glovebox door, trim panel and wing mirror backing plates
I think that's the lot... Here's some pics.
Hope you like it!
Build thread is at http://www.stanceworks.com/forums/sh...ad.php?t=11730 - doesn't really kick off until pg3.
This is my Touring - it used to be on bronze Rotas, but I put E34 M5 Contours on it last week, and it looks much better now! I usually think people writing out a full spec is a little bit ghey, but here goes anyway:
'99 E36 323i Sport Touring
Engine:
2.5-litre straight-six
aFe induction kit
Fox cat-back exhaust
Evosport power pulleys
Traction control removed
Chassis:
Spax RSX coilovers
RPM camber/castor-adjustable front topmounts
Rogue Engineering rear topmounts
Eibach anti-roll bars (though rear not installed yet, I broke a bracket so I have no ARB)
Eibach/SPC adjustable rear camber arms
Powerflex polybushes
Meyle Heavy Duty front lower arms and ball joints
Meyle Heavy Duty front ARB droplinks
TAR-OX G88 discs and Strada pads all round
Wheels/tyres:
8.5x17 ET13 (front) and 10x17 ET15 (rear) Contours, silver centres with diamond cut dishes.
195/45 and 215/40 Falken Ziex ZE912s.
Exterior:
M3 Evo splitter
M3 rear valance
Roof bars removed and carbon roof wrap
Lamin-X tint film on indicators and fogs
6000k HIDs
Matte black headlight shrouds,
323 badge removed
Kidneys painted black
US spec numberplate blank strip (not fitted in most pics)
Arches rolled & pulled
Interior:
Momo steering wheel
Alcantara gaiters with ///M stitching
E46 Clubsport gearknob
Flocked glovebox door, trim panel and wing mirror backing plates
I think that's the lot... Here's some pics.
Hope you like it!
Build thread is at http://www.stanceworks.com/forums/sh...ad.php?t=11730 - doesn't really kick off until pg3.
Comment